|
|
easynet
|
Hi, I have a problem with a driver of a MSL5026. This the message i see: did not match serial number xxxxxxxx provided by Compaq StorageWorks DLT/SDLT Minium (Changer0) among the list of drivers.
Someone knows gives some information to me?
Thanks
|
|
|
Note: If you are the author of this question and wish to assign points to any of the answers, please login first.For more information on assigning points ,click
here
|
|
|
Sort Answers By:
Date or Points
|
|
Torsten.
|
|
Nov 2, 2009 13:15:37 GMT
10 pts
|
|
|
Where did you get this message? |
|
|
easynet
|
|
Nov 2, 2009 14:16:00 GMT
N/A: Question Author
|
|
|
On the eventviewer from the server, which the storage is connected |
|
|
Torsten.
|
|
Nov 2, 2009 14:21:24 GMT
10 pts
|
|
|
Who complains? The backup application? |
|
|
easynet
|
|
Nov 2, 2009 16:54:24 GMT
N/A: Question Author
|
|
i wonna use NTBACKUP on W2003 server.
if ai connet in SCSI the LTO to the server, it see two DLT and a Changer. but if i connet it in Fiber Channel, the server mount 1 DLT and a Changer, and in the event viewer i see that error |
|
|
Torsten.
|
|
Nov 3, 2009 10:34:45 GMT
10 pts
|
|
The information flows bit by bit into this thread ...
You should check the NSR discovery and mapping page now. |
|
|
Nexis Support Engineer
|
|
Nov 3, 2009 11:22:25 GMT
10 pts
|
|
|
The barcode reader has a problem |
|
|
Torsten.
|
|
Nov 3, 2009 11:28:38 GMT
10 pts
|
|
|
The barcode reader will make a drive invisible? Why? |
|
|
easynet
|
|
Nov 3, 2009 15:24:03 GMT
N/A: Question Author
|
|
|
if The barcode reader has a problem, why it works fine in SCSI e not in FC ? |
|
|
Torsten.
|
|
Nov 3, 2009 15:31:26 GMT
10 pts
|
|
|
Did you check the NSR already? Any results? |
|
|
easynet
|
|
Nov 3, 2009 16:09:34 GMT
N/A: Question Author
|
|
|
excuse me, how can i check the nsr mapping ? is there a web interface on the FCtoSCSI router? ora by serial cable ? may i know the right commands to show the mapping ? |
|
Uwe Zessin
|
|
Nov 3, 2009 16:17:10 GMT
10 pts
|
|
|
Yes, there are a Web and a Telnet interface and with the special cable you can also make a serial connection (but do not confuse the MSL cable with the NSR cable). |
|
|
easynet
|
|
Nov 5, 2009 11:57:35 GMT
N/A: Question Author
|
|
i plugged the eth in the switch. the leds is green. but the switch not listen any mac.
swt-002-esn#sh mac-address-table interface f0/17
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
the guide tell this :
Default Ethernet settings
The basic factory default values are:
IP address: http://1.1.1.1/
Subnet mask: 255.255.255.0
Gateway address: 0.0.0.0
User name: root
Password: password
but pinging it, no responce.
i tried to reset the FC device too but maybe because it is refurbished, the ip was changed |
|
|
Torsten.
|
|
Nov 5, 2009 13:36:40 GMT
10 pts
|
|
Newer NSR model and newer firmware has a default IP setting of DHCP!
To change this, you need a serial connection. |
|
|
easynet
|
|
Nov 5, 2009 16:26:47 GMT
N/A: Question Author
|
|
|
it is possible, but why from switch i dont see any mac-address from f0/17 where plugged the cable ? if the device asks for DHCP ip i'll see the mac in the show mac-address output! |
|
|
Torsten.
|
|
Nov 5, 2009 17:08:44 GMT
Unassigned
|
|
|
Power cycle the box to ensure it is not hung. Connect to serial port and see what it does. |
|
|
easynet
|
|
Nov 5, 2009 17:39:23 GMT
N/A: Question Author
|
|
|
the serial cable have a part number ? to order it |
|
|
Torsten.
|
|
Nov 5, 2009 17:41:54 GMT
Unassigned
|
|
|
Should be delivered with the box. Caution - there are 2 different cables (for library and NSR), they look similar, but are different! |
|
|
easynet
|
|
Nov 5, 2009 18:14:56 GMT
N/A: Question Author
|
|
|
i bought a used device, no cable. how can i buy the right one ? |
|
Printable version
